Electrical Panel Upgrade in Dallas, TX

Licensed master electrician. City of Dallas permits, Oncor coordination, and final inspection handled start to finish by Kravolt Electric.
State-Licensed Master Electrician · TECL #40613 [verify on TDLR]

If your electrical panel is buzzing, hot to the touch, smells like burning, or throws sparks

Stay clear of it and call 911 first. If it is safe to do so, switch the main breaker off. Then call our emergency line at (214) 222-0320.

Dallas's Local Electrician for Panel Replacement

Your electrical panel is the control center for every circuit in your home. When it is outdated, overloaded, or damaged, everything it feeds is at risk. If you are searching for an electrical panel upgrade in Dallas, TX, Kravolt Electric gives you a clear diagnosis, a written quote, and a licensed master electrician involved from the first inspection through the city’s final approval.

We upgrade 100-amp services to 200 amps, replace worn and outdated breaker panels, and remove hazardous legacy brands. Whether you are adding an EV charger, replacing an old A/C system, or finishing a renovation, we make sure your home’s electrical service is ready for the load.

Signs Your Dallas Home Needs a Panel Upgrade

Panels usually warn you before they fail. Call us if you notice any of these:

Why Older Dallas Homes Outgrow Their Electrical Service

Dallas is a big city with a big range of housing, from classic mid-century homes in East Dallas and Lakewood to established properties in North Dallas, Oak Cliff, and Lake Highlands. [Verify build-era details before adding dates.] Many older homes in these areas still run on their original 100-amp service or on outdated split-bus panels.

Those systems were designed for a very different household. Today a typical home runs central air through long Texas summers, plus home offices, smart-home equipment, modern kitchen appliances, and often an EV charger, all at once. When a panel is asked to carry more than it was designed for, you see nuisance trips, flickering lights, warm breakers, and loose connections. An upgraded panel removes that strain and gives your home room to grow.

Problems We Correct in Dallas Homes

Overloaded 100-amp panels

Frequent breaker trips and lights that flicker when the A/C kicks on are classic signs that your service is undersized.

Outdated split-bus panels

Panels without a single main disconnect make it harder to shut off power in an emergency and often can’t accept modern protection devices.

Weather wear at exterior equipment

North Texas heat, storms, and temperature swings take a toll on aging risers, meter sockets, and weatherheads. We replace damaged equipment as part of the project.

Hazardous legacy brands

FPE Stab-Lok and Zinsco panels have documented histories of breakers that fail to trip during overloads. We recommend replacing them rather than repairing them.

Missing modern protection

We install code-required arc-fault (AFCI) and ground-fault (GFCI) protection, and surge protection and grounding updates where required.

How Our Panel Replacement Process Works

Replacing a main panel involves your city and your utility, not just an electrician. We manage every step.
  1. Free in-home inspection and quote. We evaluate your panel, meter base, service entrance, and grounding, then give you a written quote with no surprises.
  2. City of Dallas permit. We submit the electrical permit before work begins.
  3. Oncor coordination. Your service must be temporarily disconnected and reconnected by Oncor. We arrange the request so the outage is as short as possible. Oncor sets the final timing, and we keep you informed.
  4. Installation. Your master electrician and crew remove the old panel, install the new one with a main disconnect and correctly rated breakers, label every circuit, and update grounding as required.
  5. City inspection. We schedule and attend the final inspection and correct anything the inspector flags. After the work passes, power is restored.
  6. Walkthrough. We show you your new panel, explain the labeling, and answer your questions.

Code Compliance You Can Count On

Our installations follow the National Electrical Code edition currently adopted in Texas, along with any City of Dallas amendments. That means correct breaker types, proper grounding and bonding, safe working clearances, and complete circuit labeling. It also means your job is permitted and inspected, which protects your safety, your insurance coverage, and your home’s resale value.

200 Amp Panel Upgrade in Dallas: What It Costs

Most Dallas homeowners ask about price first. A typical 200 amp panel upgrade in Dallas runs $2,500 to $4,500 or more. [Confirm against your current quotes.] Your final number depends on:

A standard quote from us includes the panel and main disconnect, breakers, permit fees, Oncor coordination, installation, and inspection. If your meter socket or riser needs replacing, it appears in the written quote before work starts, not afterward.

Flexible financing is available [add lender name and terms] so you can fix a safety issue now instead of putting it off.

Breaker Box Replacement in Dallas: Repair or Replace?

Sometimes a single breaker can be swapped and the panel stays. But if your box is a hazardous brand, shows heat damage, is crowded with doubled-up breakers, or can’t support the loads you need, breaker box replacement in Dallas, TX is the safer and often more economical choice. We’ll tell you honestly which applies to your home, and we’ll show you photos of what we found before you spend anything.

Selling, Buying, or Insuring an Older Dallas Home?

Panels are one of the most common items flagged in home inspections and insurance reviews, especially FPE, Zinsco, and fuse-box systems. If a buyer’s inspector or your insurer has raised a concern, we can inspect the panel, explain exactly what was found, and quote the fix in writing. A modern, permitted, properly labeled panel removes a common negotiating point and gives the next owner confidence.

Recent Dallas Panel Upgrades

[Replace with 3 real Dallas jobs, with customer permission.]

[Neighborhood], Dallas: [Project title]

[Starting panel and result. Add a real job photo above this card with Dallas in the alt text.]

[Neighborhood], Dallas: [Project title]

[Starting panel and result. Add a real job photo above this card with Dallas in the alt text.]

[Neighborhood], Dallas: [Project title]

[Starting panel and result. Add a real job photo above this card with Dallas in the alt text.]

Why Dallas Homeowners Choose Kravolt Electric

Frequently Asked Questions

Yes. Replacing a main panel or upgrading service capacity requires an electrical permit and an inspection from the City of Dallas. Kravolt Electric handles the permit submittal and inspection scheduling. [Confirm with the City of Dallas and link the permit page.]

Most panel upgrades are completed in a single day. Oncor disconnects and reconnects the service, and reconnection follows a passed city inspection, so exact times depend on their schedule. We coordinate both and keep you informed throughout.

It can help. A modern 200-amp panel improves safety, addresses a common inspection and insurance concern, and gives the next owner capacity for modern appliances and EV chargers. It doesn’t guarantee a higher sale price, but it removes a common obstacle in a sale.

Both brands have documented histories of breakers that fail to trip when overloaded, which can lead to overheating. Many insurers and home inspectors flag them. We recommend replacement and can inspect yours for free.

In most cases, yes. We evaluate your existing service during the inspection. If the line and equipment can support 200 amps, we replace the meter socket and weatherhead as needed and coordinate with Oncor. If the line needs upgrading, we’ll explain what that involves.

Yes, and it’s often the smartest time to do it. A 200-amp panel provides the breaker space and capacity for a Level 2 charger alongside your household loads. We confirm the numbers with a load calculation first.

Ready to Upgrade Your Panel?

Don’t wait for a warning sign to become an emergency. Schedule your free in-home inspection for an electrical panel upgrade in Dallas, TX with Kravolt Electric today.
State-Licensed Master Electrician, TECL #40613 [verify]. [Add company electrical contractor license number.]
Scroll to Top