Whole-Home Surge Protection in Dallas-Fort Worth
A power strip is not whole-home protection
One Device at Your Panel Protects the Whole House
Modern homes are full of electronics that a power surge can damage in a flash or wear out over time. Control boards in your A/C, the processors in your refrigerator and oven, your Wi-Fi equipment, and your EV charger all depend on clean, steady voltage. A whole-home surge protective device (SPD) installed at your main panel gives every circuit in the house a first line of defense, including the hardwired equipment a power strip can’t reach.
Kravolt Electric installs whole-home surge protection across Dallas, Garland, Mesquite, and Rowlett. Each job is led by a state-licensed master electrician, starting with a quick look at your panel and grounding to make sure the device will work the way it should.
Why Dallas-Fort Worth Homes Need Whole-House Surge Protection
North Texas gets severe storms, lightning, and sudden grid events. Utility switching, storm damage, and the restoration of power after an outage can all send a spike down the line toward your home.
But storms are only part of the story. Industry sources commonly estimate that most surges start inside the home, when motors and compressors cycle on and off. [Confirm the statistic and source before quoting a percentage.] Your A/C compressor, pool pump, and large appliances create small voltage disturbances every time they start. Over months and years, those repeated hits can wear down sensitive circuit boards and shorten the life of expensive equipment. A larger external surge, from the utility or from lightning nearby, can damage unprotected equipment instantly.
A whole-home SPD helps with both. It limits the voltage that reaches your circuits, and it sends the excess energy to ground through your home’s grounding system.
Equipment We Help Protect
HVAC systems and heat pumps
Smart appliances
EV chargers
Electronics and home networks
Is Whole-Home Surge Protection Required by Code?
In many cases, yes. Since the 2020 National Electrical Code (NEC), Section 230.67 has required a Type 1 or Type 2 surge protective device on services that supply dwelling units. The device must be part of the service equipment or installed immediately adjacent to it. The 2023 NEC kept that requirement and added a minimum nominal discharge current rating of 10 kA.
The rule also applies when service equipment is replaced. That means if you replace your main panel, a surge protective device is part of the job. [Confirm which NEC edition the City of Dallas, Garland, Mesquite, and Rowlett currently enforce, and whether any local amendments apply.]
For homes with an older panel, an SPD isn’t automatically required by code, but it’s still one of the most cost-effective ways to protect what’s plugged in and wired up in your house.
Type 1 vs. Type 2 Surge Protection
| Device | Where it connects | What it’s for |
|---|---|---|
| Type 1 SPD | On the line side of the main service disconnect, or within the service equipment | Handles larger surge energy coming in from the utility service, and can be installed ahead of the main breaker |
| Type 2 SPD | On the load side of the main breaker, in or next to your panel | Limits surges that reach your home’s circuits, including those created inside the house |
| Type 1 + Type 2 | Both locations | Added protection layers for homes with high-value equipment |
Which Setup Is Right for Your Home?
Single-stage (Type 2 at the main panel). A good fit for most homes. It meets the code requirement where one applies and protects every circuit in the house.
Two-stage (Type 1 + Type 2). Worth considering if you have pool equipment, an EV charger, a detached garage or workshop on a subpanel, or high-value electronics and HVAC equipment. The code requires one qualifying device at the service, so a second stage is an added layer of protection, not a code mandate.
We’ll recommend the simplest setup that fits your home and explain why. We won’t upsell you.
How Our Surge Protection Installation Works
- Panel and grounding check. Your master electrician inspects your main panel, service disconnect, and grounding system. A surge device only works well if there is a solid path to ground, so we confirm that first.
- Quote and scheduling. We recommend a single-stage or two-stage setup and give you a written quote. If your setup requires work on the line side of the main disconnect, we coordinate with your utility. [Confirm the process with Oncor and Garland Power & Light.]
- Installation. We install the device with a correctly rated breaker or connection, mount it as close to the panel as practical, and keep the leads short.
- Testing and paperwork. We confirm the device’s status indicators, replace the panel cover, and give you the warranty documentation.
Whole-Home Surge Protection Pricing
- Single-stage Type 2 (main panel): $450 to $850, including the device, a dual-pole breaker, mounting, and warranty registration
- Two-stage Type 1 + Type 2: $950 to $1,650 or more, for homes with pool equipment, EV chargers, or subpanels
- Panel upgrade combo: save up to $250 when you add surge protection to an electrical panel upgrade [confirm offer terms]
What a Surge Protector Can and Can't Do
A whole-home SPD greatly reduces the risk of damage from surges, but no device can promise complete protection. A direct lightning strike carries far more energy than any residential surge protector is built to handle. For indirect strikes and utility surges, a properly installed and grounded SPD is one of the best defenses available.
Many SPDs also come with manufacturer warranties or connected-equipment coverage. Terms vary by product, so we give you the documentation and explain what it covers. [Add the specific warranty details for the brands you install.]
Planning a Panel Upgrade? Add Surge Protection Now
Service Areas
Mesquite
Rowlett
Frequently Asked Questions
No. Power strips help with small spikes at a single outlet. They don’t protect hardwired equipment such as your A/C, water heater, or EV charger, and they aren’t designed for large surges arriving from the utility line. A whole-home SPD protects every circuit from your panel.
No. A direct strike carries more energy than any residential surge protector can absorb. A properly installed and grounded SPD does reduce the risk from indirect strikes, utility switching, and surges created inside the home.
In most cases, yes, for new services and when service equipment is replaced. NEC 230.67 requires a Type 1 or Type 2 SPD at dwelling unit services. Local enforcement depends on the code edition your city has adopted. [Confirm with each city.] We handle this as part of any panel replacement.
Not for code. The NEC requires one qualifying SPD at the service. A second stage adds extra protection for homes with pool equipment, EV chargers, subpanels, or high-value equipment. We’ll recommend what fits your home.
A standard single-stage installation is usually completed in a few hours. If work on the line side of your main disconnect requires utility coordination, the schedule may depend on the utility. [Confirm your typical timing.]
No. Surge protection doesn’t reduce energy use, and it doesn’t fix flickering lights caused by loose connections or an overloaded panel. If your lights flicker, schedule an inspection and we’ll check the cause.
Yes. An SPD absorbs energy over its lifetime, and its protection can run down after many surges or one large one. Most devices have a status indicator that tells you when protection has ended. We show you what to look for and recommend checking it periodically.