Meter Socket Replacement in Dallas-Fort Worth

Licensed master electrician for meter socket, service riser, and weatherhead repairs and upgrades, with permits and utility coordination handled for you.
State-Licensed Master Electrician · TECL #40613 [verify on TDLR]

Storm damage or a utility tag? Safety first.

If a service mast or weatherhead has been torn off, wires are down, or you see sparks, smoke, or fire, stay clear and call 911. For a damaged meter base or weatherhead, call your utility first so it can safely disconnect service. For Oncor, call 888-313-6862 [verify on oncor.com]. Then call us at (214) 222-0320. We repair the equipment and handle the permit and inspection steps your city requires.

Your Meter Socket Is the Link Between the Utility and Your Home

The meter socket, sometimes called the meter base or meter can, is the weatherproof enclosure on the outside of your home that holds your electric meter. It connects the utility’s service to your main panel, and because it sits outdoors, it takes years of North Texas heat, storms, and moisture.

Kravolt Electric replaces and upgrades meter sockets, service risers, and weatherheads across Dallas, Garland, Mesquite, and Rowlett. We handle the electrical work, the permit, the city inspection, and the coordination with your utility, so you aren’t left chasing three different offices.

Who Owns What? Homeowner vs. Utility

This is the most common question we get, and it decides who has to pay for a repair. For Oncor customers, the dividing line is the meter itself.

You own and maintain

The meter socket (the enclosure), the service mast and weatherhead, and the wiring from the weatherhead to the meter and from the meter into your home. Repairs to these are the homeowner’s responsibility.

The utility owns and maintains

The meter itself, the poles, transformers, and the service lines that run from the pole to your home. Oncor does not repair customer-owned equipment.
Garland Power & Light customers should confirm GPL’s ownership rules for their address. [Confirm with GPL before publishing. These details match Oncor’s published guidance.] We check this for you during the inspection.

When Do You Need a Meter Socket Replacement?

Damaged or corroded equipment

Rust, cracked housings, burned or pitted jaw contacts, loose lugs, or water inside the enclosure.

Storm damage

A bent or torn-off mast, a weatherhead pulled away from the wall, or a meter base knocked loose by wind or a falling limb.

A utility tag or disconnect

The utility found a hazard on your equipment and disconnected service or marked it for repair.

A 200-amp service upgrade

When your service increases, the meter socket and service conductors need to be rated to match.

Flickering across the whole house

Loose or worn contacts at the meter can cause problems throughout the home. Don’t wait on this one, because it’s also a fire risk.

Burning smell or visible arcing

Treat this as an emergency. Stay clear and call 911 first.

Storm Damage or a Hazardous Disconnect: How Restoration Works

When storm damage is on your side of the meter, the utility can’t restore power until the customer-owned equipment is fixed. Here’s the usual order of events for Oncor customers. [Confirm GPL’s process separately.]
  1. Call your utility first. If the meter base or weatherhead is damaged, the utility arranges a temporary hazardous disconnect so the repair can be made safely.
  2. We repair or replace the equipment. Your master electrician replaces the damaged meter socket, mast, weatherhead, or wiring.
  3. City permit and inspection. Many cities require a permit and an inspection before power can be restored. We handle both. After the work passes, the city sends confirmation to the utility. [Confirm each city’s process.]
  4. Request the reconnect. Once the inspection is cleared, the utility reconnects service. We coordinate the request and keep you informed.
We can’t promise exact restoration times, because the utility and city inspection schedules are outside our control. What we can do is make sure the repair is done right the first time and the paperwork is ready.

How a Planned Meter Base Upgrade Works

  1. Inspection and quote. We inspect the meter socket, mast, weatherhead, conductors, and grounding, then give you a written quote.
  2. Permit and utility coordination. We pull the electrical permit and arrange the utility’s disconnect and reconnect. The utility handles the meter itself.
  3. Installation. We install a new rain-tight meter socket that meets your utility’s requirements, along with the mast, weatherhead, and service conductors as needed, and connect the grounding.
  4. Inspection and reconnect. We schedule the city inspection and correct anything flagged. After the inspection passes and the utility is notified, service is restored.

Code and Utility Compliance

Utility specifications

Utilities set requirements for socket type, mounting height, mast clearance, and weatherhead position. We install to your utility’s current standards. If your utility requires a feature such as a lever bypass, we use a socket that meets it. [Confirm requirements with Oncor and GPL.]

Grounding and bonding

We connect the grounding electrode system and bond the equipment as the NEC and your utility’s rules require.

City permits

We file the permit before work begins in Dallas, Garland, Mesquite, and Rowlett. [Confirm each city’s requirements.]

Final inspection

We schedule and attend the inspection, and correct anything the inspector flags before service is restored.

Meter Socket Replacement Pricing

Pricing depends on the type of repair, your service size, and the condition of the mast and conductors. Typical ranges: [confirm against your current quotes]
Your written quote lists exactly what’s included before any work begins.

Upgrading Your Panel? Do the Meter Socket at the Same Time

A 200-amp panel needs a meter socket and service conductors that are rated for it. Doing both in one project means one permit, one inspection, and one utility outage. It’s also the best time to add whole-home surge protection.

Service Areas

We handle meter socket, riser, and weatherhead work in these cities.

Dallas

Permits through the City of Dallas, service through Oncor.

Garland

Served by Garland Power & Light or Oncor depending on address.

Mesquite

Permits through the City of Mesquite, service through Oncor. [verify]

Rowlett

Permits through the City of Rowlett, service through Oncor. [verify]

Frequently Asked Questions

For Oncor customers, the utility owns the meter itself, and the homeowner owns the meter socket, mast, weatherhead, and the wiring on the home side. Repairs to customer-owned equipment are the homeowner’s responsibility. [Confirm GPL’s rules for Garland customers.]

If equipment is damaged, call your utility first so it can disconnect service safely, then hire a licensed electrician. If the damage involves fire, sparks, or downed wires, call 911 first.

In most cases, yes. Many cities require a permit and inspection for meter base work, and the utility may not restore service until the city confirms the work passed. We pull the permit and schedule the inspection. [Confirm each city’s requirements.]

A planned replacement is usually done in one day. The utility and city inspection set the exact timing, so we can’t promise specific hours. After storm damage, timing also depends on how many customers the utility is serving. We keep you informed throughout.

We don’t recommend it. The service side of the meter stays energized unless the utility disconnects service, and the work requires a permit and inspection. Texas has rules about who can do this work. [Confirm homeowner exemption rules with TDLR and your city.]

Look for rust, cracks, loose or leaning equipment, water inside the enclosure, burn marks, or a burning smell. Flickering lights throughout the house can also point to a loose connection. If you’re not sure, schedule an inspection.

Usually yes. The meter socket and service conductors need to be rated for the new service size. We confirm exactly what’s needed during the inspection and put it in the written quote.

Need a Meter Socket Replaced?

Schedule a meter base inspection with Kravolt Electric. We’ll tell you what’s damaged, what the utility and city require, and what it will cost.
State-Licensed Master Electrician, TECL #40613 [verify]. [Add company electrical contractor license number.]
Scroll to Top