EV Charger Guide

Will Your Panel Handle an EV Charger? Load Calculations for Dallas, Mesquite, Garland and Rowlett

Reviewed by a state-licensed master electrician (TECL #40613 [verify on TDLR]) · Kravolt Electric
It depends on a calculation, not just the size of your panel. A 100-amp panel in a home with electric cooking and central air often can’t take a fast charger. A 150-amp panel sometimes can. A 200-amp panel almost always can. This guide shows how the math works, so you know what your electrician is doing and what your options are if the panel comes up short.

The short version

The charger side: breaker and wire size

The National Electrical Code (NEC) treats EV charging equipment as a continuous load, meaning it runs at full current for three hours or more. Continuous loads get a 25% safety margin, so the breaker has to be rated at 125% of the charger’s current. That’s why a 48-amp charger sits on a 60-amp breaker.
Charger outputLoad at 240VBreakerTypical copper wire
16 A3,840 VA20 A#12
24 A5,760 VA30 A#10
32 A7,680 VA40 A#8
40 A9,600 VA50 A#6
48 A11,520 VA60 A#6
Wire size also depends on how long the run is, how it’s installed, and the terminal ratings, so your electrician confirms it for your house. The point of the table is that the breaker size is fixed by the charger. What’s left is whether the panel has room for it.
As a rough guide, a 32 to 48-amp charger adds enough range overnight for most daily driving. Exact speed depends on your vehicle.

The panel side: the load calculation

A panel isn’t measured by what’s connected, because nothing in your house runs all at once. The NEC lets an electrician add up your loads, apply demand factors for the fact that they don’t overlap, and compare the total to your service size. There are three common ways to do it:

What changed in the 2026 NEC

Texas adopted the 2026 NEC effective September 1, 2026. [Confirm with TDLR and your city, since projects permitted earlier may fall under the 2023 edition.] For load calculations, three changes matter:
Together, those changes make the 2026 math more favorable for many houses than the 2023 math. Your city’s plan reviewer decides which method and edition apply, so ask what they want to see before the permit is filed.

A worked example

Here’s a typical 2,100-square-foot Dallas-area home: electric range, dryer, and water heater, a 4-ton A/C, and gas heat. This is an illustration using the 2026 optional method, not a substitute for a real calculation with your actual nameplate ratings.
LoadVA
General lighting: 2,100 sq ft × 2 VA4,200
Kitchen small-appliance circuits (2) and laundry circuit4,500
Electric range12,000
Electric dryer5,000
Electric water heater4,500
Dishwasher1,200
General loads total31,400
First 8,000 VA at 100%8,000
Remaining 23,400 VA at 40%9,360
Subtotal after demand factors17,360
4-ton air conditioner (nameplate, gas heat assumed)6,000
Total without a charger23,360 VA (about 97 A)
Plus a 48 A charger (11,520 VA)34,880 VA (about 145 A)
Plus a 32 A charger (7,680 VA)31,040 VA (about 129 A)
Panel sizeCapacity48 A charger32 A charger
100 A24,000 VADoes not fitDoes not fit
150 A36,000 VAFits, barelyFits
200 A48,000 VAFitsFits
Notice two things. First, this house is already at about 97 amps before the charger, so a 100-amp panel is out. Second, the 150-amp result is close. If the same house had 10 kW of electric strip heat instead of gas heat, the total would pass 36,000 VA with the 48-amp charger and the 150-amp panel would no longer fit. Small differences in the house change the answer, which is why it takes a calculation and not a rule of thumb.

If your panel is maxed out

When the calculation doesn’t fit, there are three code-compliant ways forward.

1. Upgrade to 200-amp service

Best when the panel is old, the brand is a known problem (Federal Pacific, Zinsco), or you’re planning a second EV, a pool, or electric cooking. The job usually includes a new meter socket and a surge protective device, and the utility handles the disconnect. See our panel upgrade service areas.

2. Add load management

A listed energy management or power control system monitors your service and slows or pauses the charger when the house needs the power. The NEC allows the calculation to use that limit instead of the charger’s full rating, and the 2026 edition recognizes these systems more formally. It’s a good fit for a healthy 150-amp panel where a full upgrade isn’t justified. Your inspector has to accept the system, and the equipment must be listed. [Confirm each city’s position.]

3. Install a lower-amperage charger

Setting a charger to 24 or 32 amps lowers its load on the calculation. Under the 2026 NEC the calculation uses the charger’s nameplate or restricted setting. Under the 2023 NEC a 7,200 VA minimum applied, so lowering it below that gave no benefit. Ask your city which edition it’s applying. A 32-amp charger still covers most overnight charging.

Permits and utilities

Installing a new 240-volt circuit for a charger needs an electrical permit and a city inspection in the cities we serve. [Confirm each city’s requirements.] Texas licensing rules require a licensed electrician for most residential work, with a homeowner exemption that cities can limit. We explain how that works in our permit and inspection guide.

The utility only gets involved if the project includes a service upgrade. Then Oncor or Garland Power & Light disconnects and reconnects power, and the city inspection comes first. Our meter socket page covers what changes at the meter.

For code references, see NFPA 70, the National Electrical Code, and the Texas Department of Licensing and Regulation’s electrician page to check any electrician’s license.

Hardwired or plug-in?

Chargers connect two ways. A plug-in unit uses a NEMA 14-50 receptacle. A hardwired unit connects directly to the circuit.
We recommend hardwiring for 40 to 48-amp chargers. A receptacle carrying a high continuous load for hours is a common heat problem, and worn contacts make it worse. If you do use a receptacle, the NEC requires ground-fault protection for it. Hardwired chargers already include their own ground-fault protection, so a separate GFCI breaker usually isn’t needed. Check the manufacturer’s instructions.
A separate disconnect switch is required for chargers rated above 60 amps, so most home chargers don’t need one unless your city says otherwise. [Confirm local amendments.]

Frequently asked questions

Rarely. In most homes with electric cooking, a dryer, and central air, the calculation exceeds 100 amps before the charger is even added. A lower-amperage charger or load management can sometimes work in a lighter-use home. The calculation decides.

Usually, yes. Many cities want one with the permit, and it’s the only way to know the panel is safe for the added load. Ask your city what documents it requires. [Confirm each city.]

Only with care. A dryer circuit is typically 30 amps, so continuous charging should stay at 24 amps or less. Use a listed splitter or charging adapter, not a homemade one, and replace a worn receptacle. A dedicated circuit is a better long-term answer.

A circuit and hardwired charger is often a few hours. A panel or meter upgrade takes longer, and the utility and city inspection set the timing. We’ll give you a realistic window in the quote. [Confirm your typical timing.]

No. Many homes run a Level 2 charger on 100 or 150 amps. It depends on the calculation, the charger’s amperage, and what else the house runs.

A modern panel with room to add circuits is a selling point for many buyers, but it doesn’t guarantee a higher price. Think of it as removing an obstacle, not adding value on paper.

Get a real answer for your house

Schedule an on-site panel inspection. We’ll run the load calculation, tell you what fits, and give you a written quote that includes permits.
State-Licensed Master Electrician, TECL #40613 [verify]. [Add company electrical contractor license number.]

1 thought on “EV Charger Panel Load Calculations in DFW | Kravolt Electric”

  1. Pingback: 2026 Breaker Box Replacement Cost: 100A vs. 200A Upgrade

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top